Function keys
The basic version of the device has six function keys which you can program to suit your needs. Each function key has a multi-colour LED that indicates its status, based on its assignment.
The number of programmable function keys on the COMfortel D-200 or D-210 can be extended by adding up to three COMfortel D-XT20 or D-XT20i key extension modules (not included in the scope of delivery). Modules are attached to the right-hand side of the phone.
Note: If you connect more than one key extension module, use a COMfortel D-XT-PS power supply unit (not in the scope of delivery).The programmable function keys can each be defined three times (on three levels). Consequently, in the fully extended system, there are 198 programmable settings on 66 buttons.
Note: New parameters have been defined for some function keys (e.g. Speed dial) from firmware version 1.10. If functionality is restricted following an update to a higher firmware version, it might be sensible to delete the particular key and then configure it again.LED signalling
Each LED indicates the status depending on the key definition.
*: The function key or the described behaviour of the LED is only visible if the function key has been provisioned by a PBX or activated by manufacturer templates.
**: The function key or the described behaviour of the LED is only visible if the function key was added by importing the corresponding template.
Function | LED display | Status |
|---|---|---|
Speed dial | shining red | Outgoing call from speed dial number or currently active conversation on speed dial number |
flashing red | Inbound call to the speed dial number | |
flashing green | Missed call from speed dial number | |
shining green | Registered target subscriber | |
off | No active calls or conversations | |
flashing yellow | Sending subscription to PBX | |
shining yellow | Subscription failed | |
unregistered target subscriber with enabled functionSignal presence | ||
Identity | shining green | Active, registered identity, not a standard identity |
off | Active, registered identity, not a default identity | |
flashing yellow | current registration attempt | |
shining yellow | incorrect identity | |
Call waiting | shining green | Function enabled |
off | Function disabled | |
Do not disturb | shining red | Function enabled |
off | Function disabled | |
Flashing red * | Time gap between pressing the function key and acknowledgement by the PBX/provider | |
Flashing yellow * | Current attempt to register the function key on the PBX/provider, using SIP Subscription | |
Shining yellow * | Error | |
Automatic configuration switching* | shining green | Function enabled |
off | Function disabled | |
DTMF-Relay | None | |
DTMF call | None | |
Group, Group (incoming), Group (outgoing)* | shining green | Logged into the group |
off | Logged out of the group | |
flashing green | Login process | |
flashing yellow | Sending subscription to PBX | |
shining yellow | Subscription failed | |
Activate config* | shining green | Active configuration |
off | Configuration inactive | |
Mute ringing | shining red | Ringer is off |
off | Ringer is on | |
Park position | shining red | Call in the internal park zone |
off | Free park position | |
Pickup list | None | |
Pickups | None | |
Cleaning | None | |
Relays | Flashing green (approx. 2 sec.) | Relay has been switched |
Anonymous call | shining green | Function enabled |
off | Function disabled | |
Call forwarding, on busy, on no reply, Immediately | shining green | Function enabled |
off | Function disabled | |
Flashing green * | Time gap between pressing the function key and acknowledgement by the PBX/provider | |
Flashing yellow * | Current attempt to register the function key on the PBX/provider, using SIP Subscription | |
shining yellow | Error, function key perhaps not completely configured | |
SIP message | None | |
Default identity** | shining green | active and registered identity |
Silent Alert | None | |
Call forwarding ext. Calling, on busy, on no reply, Immediately* | shining green | Function enabled |
off | Function disabled | |
flashing green | Time gap between pressing the function key and acknowledgement by the PBX/provider | |
flashing yellow | Current attempt to register the function key on the PBX/provider, using SIP Subscription | |
shining yellow | Error, function key perhaps not completely configured | |
VPN | shining green | Function enabled |
flashing yellow | Establishing VPN connection | |
off | Function disabled | |
XML Minibrowser | None |
Configuration
Web interface:
•Function keys
Details about the settings are in Function keysPhone:
•Settings > Function keys
Details about the settings are in Function keysProvisioning:
Further help in the Auerswald DokuWikiProcess for assigning function keys using the phone
1.Select a button to which a function has not already been assigned. All keys that have a function assigned to them shine yellow.
2.If necessary, use the directional pad button to switch the key level or use the soft keyLevel.
3.Press the key to which a function is to be assigned.
Note: If a key to which a function has not been assigned is pressed for a longer time (long press), the menu for configuring the selected key opens automatically.The selected key flashes yellow.
4.Select the function that is to be assigned to the key.
5.Set other necessary parameters, if necessary.
6.Confirm your entries with the soft keyOK or with OK .
The assigned key label is displayed on the display.
The key can be used with the function that has been assigned to it.
Process for assigning function keys using the Web Interface
1.Select a button to which a function has not already been assigned.
2.Change to the right level, if required (Level 1– 3 tab).
3.Select the function that is to be assigned to the key.
4.Set other necessary parameters, if necessary.
5.Save your settings.
The assigned key label is displayed on the display.
The key can be used with the function that has been assigned to it.
Extending the range of functionality using provisioning
You can use the templates in a provisioning file to extend the range of functions on the phone. These additional functions can be assigned to function keys.
Requirement for use
•Provisioning from PBX search enabled
Further help under Using provisioning•PBX firmware from Version 7.4
•Suitable template < > phone assignment on the PBX
During the next provisioning process, the configurations in the template file are loaded into the phone. The additional PBX functions are in the Choose a function (phone) or Function menu (web interface) and can be assigned to the function keys.
Further help in the Auerswald DokuWiki